Secret Box Batteries
Battery Capacity: 900mAh
Indicates how long the device will last on a full charge. A higher number means longer use.
Charging Type: 5V/0.5A USB-C
Use a USB-C charger to recharge the device. 5V/0.5A is the recommended charging rate.
Output Voltage Settings: 2.4V, 2.6V, 2.8V, 3.4V, 3.8V
Choose from different power levels to suit your various needs.
Resistance: ≥0.8Ω
The device works best with components with a resistance of 0.8 ohms or higher.
![BS-BoxBattery-3D-GroupShot-1 BS-BoxBattery-3D-GroupShot-1](https://go.blazysusan.com/hs-fs/hubfs/BS-BoxBattery-3D-GroupShot-1.png?width=2000&height=2000&name=BS-BoxBattery-3D-GroupShot-1.png)
POWERING ON/OFF
The device features auto-draw, meaning it's ready to go once connected. When you draw in, it automatically powers on without the need for any additional buttons or settings!
PREHEATING
To preheat, draw twice or press the button on the bottom twice within 1.5 seconds. The device will heat up for 15 seconds at a constant 1.8V. During this time, the indicator light will cycle through all colors, and a small flame will appear on the screen. Preheating will stop if you perform any other action.
ADJUSTING VOLTAGE
To adjust the voltage, press the button once. The device will vibrate to confirm the change. The voltage is shown by the LED color and the number of signal bars on display. The device remembers your last voltage setting, even if it has been disconnected!
2.4V: Yellow light, one signal bar
2.6V: Purple light, two signal bars
2.8V: Green light, three signal bars
3.4V: Blue light, four signal bars
3.8V: Red light, five signal bars
Ensure you are using the recommended settings for your specific cart!
POWER INDICATOR
Press the button to light up the LCD screen and check the battery's current charge level.
RESETTING THE PUFF COUNT
Click the bottom button three times, and on the third click, hold it down to reset the puff count displayed on the LCD screen.
CHARGING
The device will vibrate once to confirm the connection, and the red light will indicate that charging is in progress. Once fully charged, the light will turn green. It takes about 80 minutes to reach a full charge. Use a USB-C charger with a 5V/0.5A rating. Using an incompatible charger may cause overheating or damage to the device. Avoid using the device while it is charging, and do not leave it to charge for longer than 80 minutes or unattended.
COMPATIBILITY
The device works with most carts up to 2 grams as long as the total length, including the mouthpiece, does not exceed approximately 2 inches (5 cm). Even a 1-gram cart may not fit if its mouthpiece extends the total length beyond 5 cm. Note: Cartridges with top airflow features may not be compatible (sold separately).
LED LIGHT INDICATOR
Low Voltage: When the voltage drops below 3.2V, which can be due to battery drain, improper charging, or extreme temperatures, the red LED will flash 10 times, and the device will vibrate for 2 seconds. The screen will display 0, and the device will enter standby mode.
Charging Protection: Charging is normal with a 5V/0.5A charger. If the voltage is between 7V and 28V, the device will stop charging, and the indicator light will turn off.
Draw Timeout: If you draw for more than 10 seconds, the red light will flash 4 times, and the device will enter standby mode.
Short Circuit/Resistance Overload: The red light will flash 3 times to indicate a short circuit or resistance overload.
No Cartridge Detected: The white light will flash 3 times if no cartridge is detected.
Important Notice
To ensure your device's optimal performance, please avoid exposure to water or extreme temperatures, as it may cause malfunction.
**Disclaimer**
Blazy Susan is not liable for damages or malfunctions resulting from water exposure, improper charging, or incorrect device use. Use and dispose of the device responsibly. For more information, please visit our Help Center here.
![secret_box_1080x1080_v2 secret_box_1080x1080_v2](https://go.blazysusan.com/hs-fs/hubfs/secret_box_1080x1080_v2.png?width=2000&height=2000&name=secret_box_1080x1080_v2.png)